Review pada Pengaruh Sudut Kemiringan Atap terhadap Keluaran Energi Piezoelektrik pada Eksperimen Konversi Energi dari Tetesan Air Hujan menjadi Energi Listrik
Keywords:
piezoelectric, roof slope, energy conversion, rainwater, polycarbonate.Abstract
This review was conducted to examine the effect of variations in roof slope angles on the amount of piezoelectric energy generated from the impact of artificial rainwater. The study utilized a miniature roof model with four different slope angles: 15°, 30°, and 45°. Piezoelectric sensors were placed on the underside of the roof surface, which was made of polycarbonate material. Rain simulation was performed using a demonstration device with a constant water discharge rate and controlled droplet size. The voltage and electric current produced at each slope variation were measured using a multimeter. Each experiment was repeated three times to ensure the validity and consistency of the results. The collected data were analyzed to determine the relationship between the roof slope angle and the electrical output by presenting voltage and current graphs against the slope angle and calculating the energy conversion efficiency. The results showed that variations in the roof slope angle affected the generated piezoelectric energy, and an optimum angle was identified that produced the highest voltage and current.
Downloads
References
W. C. Widodo, Windarta, R. D. Nur’aini, and F. Maghfurah, “Pengaruh Variasi Curah Hujan dan Sudut Kemiringan terhadap Daya Keluaran pada Alat Uji Piezoelektrik,” in Prosiding Seminar Nasional LPPM UMJ, Jakarta: LPPM UMJ, 2024, pp. 1–7. [Online]. Available: http://jurnal.umj.ac.id/index.php/semnaslit
D. Pratama, I. Qiram, and A. Mukhtar, “Pengaruh Sudut Kemiringan Dan Jenis Material Atap Terhadap Tegangan Listrik Yang Dihasilkan Piezolektrik,” V-MAC (Virtual Mech. Eng. Artic., vol. 6, no. 2, pp. 71–74, 2021, doi: 10.36526/v-mac.v6i2.1521.
Z. Yang, S. Zhou, J. Zu, and D. Inman, “High-Performance Piezoelectric Energy Harvesters and Their Applications,” Joule, vol. 2, no. 4, pp. 642–697, 2018, doi: 10.1016/j.joule.2018.03.011.
M. A. Caro, S. Schulz, and E. P. O’Reilly, “Origin of nonlinear piezoelectricity in III-V semiconductors: Internal strain and bond ionicity from hybrid-functional density functional theory,” Phys. Rev. B - Condens. Matter Mater. Phys., vol. 91, no. 7, pp. 1–10, 2015, doi: 10.1103/PhysRevB.91.075203.
J. S. Yang and R. C. Batra, “Second order theory for piezoelectric materials,” Am. Soc. Mech. Eng. Des. Eng. Div., vol. 79, no. May, pp. 89–99, 1994, doi: 10.1121/1.412312.
N. A. Hill and U. Waghmare, “First-principles study of strain-electronic interplay in ZnO: Stress and temperature dependence of the piezoelectric constants,” Phys. Rev. B - Condens. Matter Mater. Phys., vol. 62, no. 13, pp. 8802–8810, 2000, doi: 10.1103/PhysRevB.62.8802.
D. G. Wakshume and M. Ł. Płaczek, “Optimizing Piezoelectric Energy Harvesting from Mechanical Vibration for Electrical Efficiency: A Comprehensive Review,” Electron., vol. 13, no. 5, 2024, doi: 10.3390/electronics13050987.
C. H. Wong, Z. Dahari, A. Abd Manaf, and M. A. Miskam, “Harvesting raindrop energy with piezoelectrics: A review,” J. Electron. Mater., vol. 44, no. 1, pp. 13–21, 2015, doi: 10.1007/s11664-014-3443-4.
J. R. Andrade, “Piezoelectric Energy Harvesting: A Comprehensive Review and Applications,” pp. 1–12, 2022.
I. Palomba, A. Doria, M. Bottin, and G. Rosati, “applied sciences Vibration Energy Harvesting from Raindrops Impacts : Experimental Tests and Interpretative Models,” 2022, doi: https://doi.org/10.3390/app12073249.
J. Ghazanfarian, M. M. Mohammadi, and K. Uchino, “Piezoelectric Energy Harvesting : A Systematic Review of Reviews,” pp. 1–40, 2021, doi: https://doi.org/10.3390/act10120312.
V. Wong, J. Ho, and A. B. Chai, “Piezoelectric energy harvesting in varying simulated rain conditions PIEZOELECTRIC ENERGY HARVESTING IN VARYING SIMULATED,” no. January, 2016.
D. Zebua, D. Kolago, Y. A. C. Wijaya, and Y. A. K. Utama, “Desain dan Pembuatan Pembangkit Listrik Tenaga Air Hujan Menggunakan Piezoelectric Disk,” J. Tecnoscienza, vol. 4, no. 1, pp. 1–16, 2019.
E. Bernat-Maso and L. E. Mercedes, “Piezoelectric elements subjected to low frequency excitation. Empirical determination of stress and frequency influence on piezoelectric parameters,” Microsyst. Technol., vol. 28, no. 8, pp. 1897–1910, 2022, doi: 10.1007/s00542-022-05331-7. K. Kunci, “DIREGANGKAN,” 2017.
K. Kunci, “DIREGANGKAN,” 2017.
A. Doria, G. Fanti, G. Filipi, and F. Moro, “Development of a novel piezoelectric harvester excited by raindrops,” Sensors (Switzerland), vol. 19, no. 17, 2019, doi: 10.3390/s19173653.
R. D. I. Leo, M. Viscardi, F. P. Tuccinardi, and M. Visone, “NUMERICAL MODELLING OF A PIEZO ROOF HARVESTING SYSTEM : THE RIGHT COMPONENT SELECTION,” vol. LXIV, 2017, doi: 10.1515/meceng-2017-0016.
W. Su, J. Lin, and W. Li, “Analysis of a Cantilevered Piezoelectric Energy Harvester in Different Orientations for Rotational Motion”.
R. Miceli, P. Romano, C. Spataro, and F. Viola, “Performances of rainfall energy harvester,” 20th IMEKO TC4 Symp. Meas. Electr. Quant. Res. Electr. Electron. Meas. Econ. Upturn, Together with 18th TC4 Int. Work. ADC DCA Model. Testing, IWADC 2014, pp. 467–472, 2014.
A. Hendriawan and D. C. Happyanto, “Piezoelectric Sebagai Alternatif Catu Daya Tambahan pada Mobil Listrik,” Inovtek, vol. 4, no. 1, p. 27, 2014.
A. W. Jayawardena and R. B. Rezaur, “Measuring drop size distribution and kinetic energy of rainfall using a force transducer,” Hydrol. Process., vol. 14, no. 1, pp. 37–49, 2000, doi: 10.1002/(SICI)1099-1085(200001)14:1<37::AID-HYP908>3.0.CO;2-M.
K. Sarjana, T. Politeknik, M. Negeri, and B. Belitung, “Pembangkit listrik menggunakan piezoelektrik dengan memanfaatkan tekanan dari pijakan kaki manusia pada lantai,” 2025.
H. F. S. S. D. R. . Julius, “APPLICATION OF PIEZOELECTRIC MATERIAL FILM PVDF (Polyvinylidene Flouride) AS LIQUID VISCOSITY SENSOR,” J. Neutrino, vol. 3, no. 2, pp. 129–142, 2012, doi: 10.18860/neu.v0i0.1648.
Syawaluddin, E. Diniardi, A. I. Ramadhan, D. Almanda, and E. Dermawan, “Analisis Desain Optimum Model Hybrid Solar Cell- Piezoelectric Dengan Cad Program,” Semin. Nas. Sains dan Teknol. 2017, no. November, pp. 1–7, 2017.
Aditya and Azhis, “G-Tech : Jurnal Teknologi Terapan,” Investig. Kemamp. Pembangkit List. Tenaga Ombak Laut Mikro Berbas. PVDF, vol. 6, no. 2, pp. 1–8, 2022, doi: https://doi.org/10.33379/gtech.v6i2.1757.
D. Y. P. Talantan, “Desain Dan Implementasi Pembangkit Listrik Tenaga Getar Turbin,” 2024.
N. Anggraini, “Prototipe Sistem Notifikasi Kecelakaan dan Wiper Otomatis pada Helm dengan Mikrokontroler Arduino,” J. Ilm. FIFO, vol. 12, no. 2, p. 213, 2021, doi: 10.22441/fifo.2020.v12i2.010.
I. Khair, S. Sasmono, and C. Ekaputri, “Analisa Tegangan Dan Arus Pada Sistem Konversi Energi Suara Menjadi Listrik Menggunakan Komponen Piezoelektrik (Voltage and Current Analysis on Sound To Electricity Conversion System Using Piezoelectric Components),” vol. 8, no. 5, pp. 4250–4258, 2021.
M. H. Alfatiha, “Perancangan Dan Implementasi Alat Pembangkit Listrik Hybrid Menuggunakan Tenaga Surya Dan Piezoelectric (P-Supir),” Aisyah J. Informatics Electr. Eng., vol. 6, no. 2, pp. 219–230, 2024, doi: 10.30604/jti.v6i2.271.
S. R. Anton and H. A. Sodano, “A review of power harvesting using piezoelectric materials (2003-2006),” Smart Mater. Struct., vol. 16, no. 3, 2007, doi: 10.1088/0964-1726/16/3/R01.
D. Almanda, E. Dermawan, A. I. Ramadhan, E. Diniardi, and A. N. Fajar, “Analisis Desain Optimum Model Piezoelektrik Pvdf Untuk Sumber Pembangkit Listrik Air Hujan Berskala Mini,” Semin. Nas. Sains dan Teknol. 2015, no. November 2015, pp. 1–5, 2015, [Online]. Available: https://jurnal.umj.ac.id/index.php/semnastek/article/viewFile/493/459
D. Almanda, E. Dermawan, E. Diniardi, Syawaluddin, and A. I. Ramadhan, “Pengujian Desain Model Piezoelektrik Pvdf Berdasarkan Variasi Tekanan,” Semin. Nas. Sains dan Teknol. 2016, no. November 2016, pp. 1–6, 2016, [Online]. Available: https://media.neliti.com/media/publications/172417-ID-pengujian-desain-model-piezoelektrik-pvd.pdf
E. Diniardi, S. Syawaluddin, A. I. Ramadhan, W. Isnaini, E. Dermawan, and D. Almanda, “Analisis Desain Pickup Piezoelektrik Dari Model Hybrid Solar Cell-Piezoelectric Untuk Daya Rendah,” J. Teknol., vol. 9, no. 2, p. 83, 2017, doi: 10.24853/jurtek.9.2.83-88.
M. Eko Saputro, M. Ilyas Hadikusuma, J. dan Teknologi Rekayasa Sistrm Elektronika, P. Negeri PontianakJl Jend Ahmad Yani, and B. Laut, “ENTRIES (JournalofElectrical Network Systems andSources) Jurusan Teknik Elektro-Politeknik Negeri Ketapang Generator Listrik Tenaga Gelombang Air Menggunakan Kristal Piezoelektrik,” vol. 04, no. 01, pp. 1–4, 2025, doi: 10.58466/entries.
E. Diniardi, S. Syawaludin, A. I. Ramadhan, N. H. Fithriyah, and E. Dermawan, “Piezoelectric Power Analysis of Low-Scale Hybrid Solar Cellpiezoelectric Model,” J. Teknol. Univ. Muhammadiyah Jakarta, vol. 10, no. 2, pp. 139–146, 2018.
E. Yulia, E. Permana Putra, E. Ekawati, and N. Nugraha, “Polisi Tidur Piezoelektrik Sebagai Pembangkit Listrik dengan Memanfaatkan Energi Mekanik Kendaraan Bermotor,” J. Otomasi Kontrol dan Instrumentasi, vol. 8, no. 1, p. 105, 2016, doi: 10.5614/joki.2016.8.1.9.
A. Kiswantono, A. Irwan, P. S. Elektro, F. Teknik, and U. B. Surabaya, “Inovasi Energi Hijau : Piezoelektrik Untuk Mengubah,” vol. 12, no. 3, pp. 1829–1835, 2024, doi: https://doi.org/10.23960/jitet.v12i3.4452.
T. Dewangga, “Studi Eksperimental Performa Sound Energy Harvesting Device Menggunakan Variasi Rangkaian Piezoelektrik,” Creat. Res. Eng., vol. 3, no. 1, p. 24, 2023, doi: 10.30595/cerie.v3i1.14314.
Comisión Económica para América Latina y el Caribe et al., No TitleНОВЫЕ ПОДХОДЫ К ОБНАРУЖЕНИЮ ФИЗИОЛОГИЧЕСКИ АКТИВНЫХ КОМПОНЕНТОВ ЖЕНЬШЕНЯ МЕТОДОМ ВЫСОКОЭФФЕКТИВНОЙ ЖИДКОСТНОЙ ХРОМАТО-МАСС-СПЕКТРОМЕТРИИ, vol. 17, no. 2. 2016.
F. S. Jati, “Mlaku: Penerapan Teknologi Waste To Energy (Wte)Sampah Plastik Menjadi Piezoelectric Paving BlockMelalui Sustainable Community,” Kumpul. Esai Mhs. tentang Sikap Gener. Z terhadap Konserv. Lingkung., 2024.
D. R. Putra et al., “Energi Alternatif Melalui Getaran Beban Mekanis,” Pros. Semin. Nas. Teknoka, vol. 3, no. 2502, p. 8, 2018, doi: 10.22236/teknoka.v3i0.2802.
M. R. Kurniawan and Umar, “Pemanfaatan Treadmill Manual Sebagai Penghasil Listrik Dengan Menggunakan Sensor Piezoelektrik,” pp. 1–23, 2016.
Arief, Jotje, and Benny, “Pemanen Energi Listrik Dari Curah Hujan Melalui Transduser Piezoelektrik Secara Seri Dan Paralel,” J. Poros Tek. Mesin Unsrat, vol. 12, pp. 1–12, 2022.
J. Lumintang, J. Rantung, and B. Maluegha, “Pemodelan Konversi Energi Listrik Dari Curah Hujan Melalui Transduser Piezoelektrik Berbasis Ansys,” J. Poros Tek. Mesin Unsrat, vol. 13, no. 2, pp. 82–93, 2024.
Y. Arimurti, Y. Radiyono, and S. Surantoro, “Studi Awal Implementasi Transduser Piezoelektrik sebagai Piranti Pemanen Energi pada Lantai,” J. Ilmu Fis. | Univ. Andalas, vol. 12, no. 2, pp. 89–97, 2020, doi: 10.25077/jif.12.2.89-97.2020.
S. Rahayu, “SINTESIS BAHAN PIEZOELEKTRIK BNT-BT DENGAN PENAMBAHAN TA 2 O 5 MENGGUNAKAN METODE SOLID STATE REACTION,” vol. 2, no. 4, pp. 276–283, 2013.
T. Bnt-bt-bkt, A. C. Iby, A. Mahyudin, and S. Ahda, “Telah dilakukan studi awal proses pemolingan dan karakterisasi sifat listrik terhadap bahan piezoelektrik ramah lingkungan BNT-BT-BKT. Dalam penelitian ini, sintesis bahan dilakukan dengan metode,” vol. 3, pp. 2–6.
E. Stiawan and A. J. Taufiq, “Rancang Bangun Alat Pemanen Energi Listrik Dari Tekanan Mekanik Berbasis Piezoelektrik,” J. Ris. Rekayasa Elektro, vol. 2, no. 2, pp. 79–84, 2020, doi: 10.30595/jrre.v2i2.8280.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Prosiding Seminar Nasional Teknoka
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Supported by :
