Mesin Pengupas Bawang Mudah – Alih (Portable Onion Peeler Machine)

  • Sahrudin Sahrudin Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
  • Dimas Ramadhan Putra Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
  • Jhav Sund Oktoricoento Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
  • Mohammad Mujirudin Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
  • Harry Ramza Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta

Abstract

The process of processing agricultural products into a food for the community becomes an interesting thing to know more deeply. One of them is pengelolahan onion with a lot of capacity for stripping process. In the process of onion processing there are several obstacles that make its production to inhibit one of them is in stripping the skin of onion and garlic by means of chopped to peel it. The producers often find it difficult to clean the onion skin at the time of stripping, let alone a large degree. The design of this tool is made to assist in the process of stripping the onion in large quantities using electric motor power as the driving force, the microcontroller as the brain to run the process of designed devices and load sensors to calculate the value of the weight capacity of the onion. The ties cable serves as a helper in stripping onions by banging them. With the aim of Determining the value of the efficiency of the thickness of the peel skin and the weight capacity of the onion, so that the best variation to be used is the variation of the combination with a value of efficiency of 17% for thickness and 3% for the weight capacity of the onion.

Author Biographies

Sahrudin Sahrudin, Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
Department of Electrical Engineering Faculty of Engineering
Dimas Ramadhan Putra, Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
Department of Electrical Engineering Faculty of Engineering
Jhav Sund Oktoricoento, Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
Department of Electrical Engineering  Faculty of Engineering
Mohammad Mujirudin, Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
Department of Electrical Engineering Faculty of Engineering
Harry Ramza, Universitas Muhammadiyah Prof. Dr. Hamka, Jakarta
Departemen Teknik Elektro Fakultas Teknik

References

Wahyu deka sidik, 2017,Rancang Bangun Mesin Pengupas Bawang(bagian poros), Fakultas Teknik Mesin Universitas sebelas maret. Surakarta

Hartono Baswarsiati. E, Karlina., Abu, dan T. Siniati, 2014. Teknologi bawang merah berbasis Good Agriculture practices Direktorat Jendral Holtkultura, Departemen Pertanian.

Darmawan .H, 2016, Pengatar Perancangan Teknik, Direktorat Jendral Pendidikan Tinggi; Jakarta.

Tartono,2015, Perancangan Mesin Pengupas Kulit Kentang Kapasitas 3 Kg/Proses. Yogyakarta

Badaruddin, 2015,Prinsip Dasar Kerja Motor Listrik. Jakarta

(http://www.learnengineering.org), Single Phase Induction Motor diakses tanggal 2013

(http://www.insinyoer.com) , Prinsip Kerja Motor Induksi 1 Fasa diakses tanggal 2015

Atmel Atmega640/V-1280/V-1281/V-2561/V[DATA SHEET]. (2014). Blok Diagram AVR Architecture, USA: 1600 Tecnology Driver,San Jose

Arduino Datasheet, Atmel Corporation,2015.

Anonim,2010,KarakteristikLCD,http://digilib.petra.ac.iddiakses tanggal 10 Juni 2010

Indraharja.(2012) Pengertian Buzzerhttp://indraharja.wordpress.com 2012/01/07/pengertian-buzzer/. diakses 20 Juli 2017.

Sensor berat load cell www.ricelake.com Load Cell and Weight(AmericaModule H : 2010)

Darmawan .H, 2016, Pengatar Perancangan Teknik, Direktorat Jendral Pendidikan Tinggi; Jakarta.

Budiharto, Widodo, “Panduan Lenkap Belajar Mikrokontroler dan Aplikasi Mikrokontroler”, PT Elex Media Komputindo,2016.

Andrasto Tatyantoro, Pemantauan Temperatur dan Kelembaban Pada Rumah Kaca Berbasis Mikrokontroler Arduino dan prototype pengiris bawang, Jurnal Teknik Elektro Vol.3 No.2,2015

Muhammad Randi ,Samadi, budi dan Cahyono Bambang, 2015, Bawang Merah Intensifikasi UsahaTani.Yogyakarta : Kanisius
Published
2018-12-22
How to Cite
SAHRUDIN, Sahrudin et al. Mesin Pengupas Bawang Mudah – Alih (Portable Onion Peeler Machine). Prosiding Seminar Nasional Teknoka, [S.l.], v. 3, p. E43-E49, dec. 2018. ISSN 2580-6408. Available at: <https://journal.uhamka.ac.id/index.php/teknoka/article/view/2819>. Date accessed: 18 mar. 2019. doi: https://doi.org/10.22236/teknoka.v3i0.2819.

Most read articles by the same author(s)

Obs.: This plugin requires at least one statistics/report plugin to be enabled. If your statistics plugins provide more than one metric then please also select a main metric on the admin's site settings page and/or on the journal manager's settings pages.