Tinjuan Pustaka: Analisis Ergonomi Posisi Berkendara pada Rangka Chopper Berdasarkan Antropometri Pengendara
DOI:
https://doi.org/10.22236/teknoka.v10i1.22732Keywords:
ergonomics, anthropometry, riding posture, chopper frame, comfort, safetyAbstract
Ergonomic analysis of riding posture on a chopper frame based on rider anthropometry is crucial to ensure comfort and safety during riding. This study examines the suitability of the chopper frame's dimensions with the rider's body size using representative anthropometric data. Through measurement and comparison methods, the research identifies geometric mismatches in seating position and control placement that can cause discomfort, muscle fatigue, and long-term injury risks. The analysis results indicate that seat dimensions and frame height need adjustment to match the rider’s anthropometric percentiles to optimize an ergonomic riding posture. This research offers ergonomic design recommendations for chopper frames to enhance comfort and reduce injury risks, using anthropometry as a design reference for two-wheeled vehicles. The findings are expected to guide the development of safer and more comfortable chopper motorcycles, supporting national ergonomic standards
Downloads
References
Hendri Mulyana, Utamy Sukmayu Saputri, Ardin Rozadi, and Lugovaya Nika Vyaceslavovna, “Modeling Low Income Vehicle Ownership in Cibadak District,” Int. J. Eng. Appl. Technol., vol. 5, no. 1, pp. 38–46, 2021, doi: 10.52005/ijeat.v5i1.58.
Abdul Kudus Zaini and Andika Ronaldo Arman, “An Analysis of Heterogeneous Traffic Dominated by Motorcycles at Signalized Intersections in Pekanbaru,” J. Pengabdi. Masy. dan Ris. Pendidik., vol. 3, no. 4, pp. 727–731, 2025, doi: 10.31004/jerkin.v3i4.888.
A. B. L. Soeoed, “Pertukaran Sosial Di Kalangan Penghobi Modifikasi Motor Di Jakarta Selatan,” Socio-political Commun. Policy Rev., vol. 2, no. 3, 2025, doi: 10.61292/shkr.237.
A. C. J. Dywananda and Z. V. Chumaida, “Pengaturan Kendaraan Modifikasi Untuk Difabel dalam Pengoperasian Lalu Lintas dalam Prespektif Hukum Transportasi,” Media Iuris, vol. 7, no. 1, pp. 51–68, 2024, doi: 10.20473/mi.v7i1.42517.
A. Rahmadi and M. Mursalin, “Design and Analysis of Chassis Frame for Chopper-Style Motorcycle,” Media Mesin Maj. Tek. Mesin, vol. 25, no. 1, pp. 64–76, 2024, doi: 10.23917/mesin.v25i1.3224.
S. Agius, P. Farrugia, and E. Francalanza, “A decision consequence-based model to understand the phenomena in motorcycle engineering design from a human factor’s perspective,” Int. J. Des. Eng., vol. 10, no. 1, p. 72, 2021, doi: 10.1504/ijde.2021.113268.
M. Rafi, Y. H. Putri, E. Muslim, and B. N. Moch, “Analysis of motorcycle design toward female rider based on posture evaluation index (PEI) approached in virtual environment,” IOP Conf. Ser. Mater. Sci. Eng., vol. 1003, no. 1, 2020, doi: 10.1088/1757-899X/1003/1/012080.
A. Anggiana, S. Suharyatun, F. K. Wisnu, and W. Warji, “Jurnal Agricultural Biosystem Engineering Analisis Ergonomika Bagian Penghancur pada Mesin Pencacah Pakan Ternak Multiguna Ergonomic Analysis of The Crushing Part of The Multi-Purpose Chopper,” vol. 2023, no. score 5, 2023, doi: https://doi.org/10.23960/jabe.v2i3.8037
R. D. Scoz et al., “Discomfort, pain and fatigue levels of 160 cyclists after a kinematic bike-fitting method: An experimental study,” BMJ Open Sport Exerc. Med., vol. 7, no. 3, pp. 1–7, 2021, doi: 10.1136/bmjsem-2021-001096.
L. Lundin et al., “Quantifying rider posture variability in powered two- and three-wheelers for safety assessment,” Traffic Inj. Prev., vol. 25, no. 7, pp. 956–967, 2024, doi: 10.1080/15389588.2024.2351607.
E. Barberi, M. Chillemi, F. Cucinotta, and F. Sfravara, “Fast Three-Dimensional Posture Reconstruction of Motorcyclists Using OpenPose and a Custom MATLAB Script,” Sensors, vol. 23, no. 17, 2023, doi: 10.3390/s23177415.
M. Dicinta, B. R. Christata, and B. Kristyanto, “Usulan Perbaikan Fasilitas Kerja Ergonomis Berdasarkan Hasil Analisis Metode REBA pada Stasiun Pengemasan Bale,” J. Tek. Ind. Terintegrasi, vol. 8, no. 3, pp. 2397–2407, 2025, doi: 10.31004/jutin.v8i3.45862.
Z. Djunaidi and R. Arnur, “Risiko Ergonomi Ketidaksesuaian Desain dan Ukuran Tempat Duduk Sepeda Motor terhadap Antropometri pada Mahasiswa,” Kesmas Natl. Public Heal. J., vol. 9, no. 3, p. 243, 2015, doi: 10.21109/kesmas.v9i3.571.
I. Kusumadewi, Budiman, and R. Taufiqur Rohman, “Ergonomic Work Facility Design Using Anthropometric Data,” J. Mech. Manuf., vol. 4, no. 1, pp. 23–33, 2025, doi: 10.31949/jmm.v4i1.12570.
R. K. K. Wibowo, D. Dwilaksana, H. I. D. Puspita, R. P. G. Widityo, and M. Khadafi, “Ergonomic Ship Chair Design for Indonesian People,” Int. J. Innov. Res. Dev., vol. 8, no. 10, pp. 43–48, 2019, doi: 10.24940/ijird/2019/v8/i1/141377-339623-.
R. Mayangsari, I. Bagus, A. Swarmadika, I. W. Surata, and I. M. Muliarta, “Kajian ergonomi desain tempat duduk sepeda motor “ X berdasarkan antropometri pengendara Ergonomic study of ‘ X ’ motorcycle seat design based on rider anthropometry Abstract,” vol. 4, no. 2, pp. 73–79, 2024.
A. Muthiah et al., “Motorcycle riding posture: A review,” Ergonomics, vol. 62, no. 3, pp. 317–330, 2019, doi: 10.1016/j.ergon.2018.12.013.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Prosiding Seminar Nasional Teknoka
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Supported by :
